Part 21 Report - 1997-051

ACCESSION #: 9701230213 Information & Support Services P.O. Box 3707 Seattle, WA 98124-2207 January 14, 1997 G-1151-SJA-97-020 Document Control Desk United States Nuclear Regulatory Commission Washington, D.C. 20555 Reference: a) Boeing Letter G-1151-RSO-92-365 dated August 31, 1992; R. S. Orr to the NRC Operations Center b) NRC Letter Docket No. 99901227 dated August 12, 1992; L. J. Norrholm to R. S. Orr; Subject: Response to 10 CFR 21 Inquiry Dear Sir or Madam: In accordance with the reference correspondence and 10 CFR 21, Boeing is sending the NRC the attached error notice(s) received from our former software suppliers. Because of unknown current addresses, the following former customers were not notified: Reactor Controls, Inc. Echo Energy Consultants, Inc. Nuclear Applications and Systems Analysis Company (Japan) Nuclear Power Services Error notices have been sent to our other former customers. Very truly yours, Sandra J. Andrews Nuclear Administrator Phone: (206) 865-6248 FAX: (206) 865-4851 Mail Stop: 7A-33, or e-mail: Sandra.Andrews@PSS.Boeing.com Enclosure(s): GTSTRUDL Program Report Form No. 97.01 Georgia Tech Computer Aided Structural Engineering Center Georgia Institute of Technology School of Civil & Environmental Engineering Atlanta, Georgia 30332-0355 USA 404 o 894 o 2260 404 o 894 o 8014 FAX JAN 14 1997 CONTRACTS Attention: Nuclear Administrator Boeing Information & Support Services P.O.Box 24346, M/S 7A-33 Seattle, Washington 98124-0346 RE: GT STRUDL Dear Sir or Madam: Enclosed please find copies of GTSTRUDL PROGRAM REPORT FORM No. 97.01 and a VENDOR ACKNOWLEDGMENT FORM. Please sign and return the VENDOR AC- KNOWLEDGMENT FORM to acknowledge receipt of the GTSTRUDL Program Report. Thank you for reviewing the Program Report and for returning the Acknowledgment Form. Best regards, CASE Center Lawrence F. Kahn Director LFK/tlk Enclosures An Equal Education and Employment Opportunity Institution A Unit of the University System of Georgia GTSTRUDL Program Report Form GPRF No.: DATE: FROM: Computer-Aided Structural Engineering Center Georgia Institute of Technology Atlanta, Georgia 30332-0355 SEVERITY LEVEL: X URGENT Problem results in incorrect answers which may not be apparent or job aborts and cannot be recovered within the session or job. _ SERIOUS Problem results in incorrect answers which are obvious or problem prevents completion of a particular user's task. _ MINOR Problem can be worked around or problem poses high frustration factor. _ INFORMATIVE Documentation error, program usage tip, user inconveniences. Date Problem Confirmed Date Notification Sent Computers All Operating System All Version 94, 01 and later Target Release for Correction 96.02 Mgr, ASD Signature Title R & D Division Michael H. Swanger Typed or Printed Name Date of Signature Signature Title Professional Services Division Typed or Printed Name Date of Signature Rev. 2.2 GTSTRUDL Program Report Form (Continued) GPRF No.: DATE: DESCRIPTION Joint classification using the CHORDS FOR PUNCHING SHEAR AUTOMATIC command may abort for a particular joint at which two colinear members of equal maximum outside diameter cannot be determined. There are two possible workarounds for this problem: 1. Make certain that all joints to be classified automatically using the CHORDS FOR PUNCHING SHEAR AUTOMATIC command have two colinear members of equal outside diameter, where this outside diameter is the maximum of the outside diameters of all members incident on the joint. 2. Manually classify the joints in question using the explicit CHORDS FOR PUNCHING SHEAR command. Relevant User's Manual Sections: CHORDS FOR PUNCHING SHEAR Command: Explicit Joint Classification Section 4.3. 1, Volume 8 CHORDS FOR PUNCHING SHEAR AUTOMATIC Command: Automatic Joint Classification Section 4.3.2, Volume 8 Rev. 2.2 *** END OF DOCUMENT ***

Page Last Reviewed/Updated Friday, January 31, 2020