Event Notification Report for March 06, 2009
U.S. Nuclear Regulatory Commission
Operations Center
EVENT REPORTS FOR
03/05/2009 - 03/06/2009
General Information or Other
Event Number: 44900
Rep Org: TEXAS DEPARTMENT OF HEALTH
Licensee: DR. PEPPER
Region: 4
City: IRVING State: TX
County:
License #: G01697
Agreement: Y
Docket:
NRC Notified By: RAY JISHA
HQ OPS Officer: DAN LIVERMORE
Licensee: DR. PEPPER
Region: 4
City: IRVING State: TX
County:
License #: G01697
Agreement: Y
Docket:
NRC Notified By: RAY JISHA
HQ OPS Officer: DAN LIVERMORE
Notification Date: 03/12/2009
Notification Time: 15:04 [ET]
Event Date: 03/06/2009
Event Time: 00:00 [CDT]
Last Update Date: 03/18/2009
Notification Time: 15:04 [ET]
Event Date: 03/06/2009
Event Time: 00:00 [CDT]
Last Update Date: 03/18/2009
Emergency Class: NON EMERGENCY
10 CFR Section:
10 CFR Section:
Person (Organization):
THOMAS FARNHOLTZ (R4)
JOHN RAMSEY (OIP)
ANDREW MAUER (FSME)
ILTAB EMAIL (ILTA)
THOMAS FARNHOLTZ (R4)
JOHN RAMSEY (OIP)
ANDREW MAUER (FSME)
ILTAB EMAIL (ILTA)
AGREEMENT STATE REPORT - TWO SOURCES DISPOSED AS SCRAP
"On February 20, 2009 during an internal audit/inspection, it was discovered that two Filtec Model FT 50 level detection devices each with 100 mCi of Am-241 were missing [and] apparently moved off the facility as scrap metal. Notification to state offices were through inappropriate channels and thus Incident Investigation staff were not informed of [the event] until March 12, 2009. A preliminary investigation has determined that the metal scrap along with these devices was subsequently shipped to a mill in India and [has] probably been melted. Specific details of the shipping, route and mode of transport, vendors as well actual location in India are being gathered. The serial numbers are 112733/5393 and 116813/2555."
Texas Incident # I-8618
* * * UPDATE ON 03/13/2009 AT 1400 FROM RAY JISHA TO DAN LIVERMORE * * *
Report received via e-mail:
"The gauges were accidentally removed from the plant and placed into a metal scrap dumpster and picked up from our property by MC3 International Scrap Salvage on December 8, 2008.
"MC3 International Scrap Salvage delivered the mixed shear cut metal to Lone Star Fox Export Metals on December 8, 2008. Lone Star Fox Export shipped the mixed cut metal to India before or around December 13, 2008. The licensee provided a list of 10 containers.
"The mixed metal was sent to Nhava Sheva, India. The licensee does not have any information on the mill in India. They do not have any information on products that may have been produced from the scrap.
"The state is in the process of contacting the scrap metal dealers. Additional information will follow as it is obtained."
Notified R4DO (Farnholtz), FSME EO (McIntosh), OIP (Ramsey), and ILTAB (via email).
* * * UPDATE ON 03/18/2009 AT 1253 FROM RAY JISHA TO VINCE KLCO * * *
Report received via e-mail:
"On Monday, March 16, 2009 [State of Texas] staff proceeded to Dr. Pepper Bottling Company (DP) in Irving, TX, General License Acknowledgement (GLA) G01697. This was in response to a report that two gauges were removed from the facility, potentially sheared at a local area scrap yard, and then shipped to India as feed for a steel mill. Upon arrival [state personnel] interviewed the Manager of Environmental Health and Safety and the Maintenance Manager in order to investigate the details of the two missing fixed fill level gauges (Industrial Dynamics, FT-50 containing 100 mCi, Am-241 each). The current contact person listed on the permit, was out of town at the time of this investigation.
"This gauge is a stainless steel box with overall head dimensions of 17 inches high, 4 ¢ inches wide and 19 ¢ inches long. These particular models have a manual shutter that was assumed to have been closed when the device was taken off-line. The Industrial Dynamics Source model 06110 is a matrix Americium 241 oxide and ceramic powder fired into a cavity 2 inches wide, 2 inches high and 1 3/8 inches deep. There is a 0.005 inch thick radiation window and when the shutter is closed, the radioactive material is covered on all sides by at least 0.5 inch of stainless steel.
"Apparently, the gauges were taken out of service some years back and stored in a used or discarded equipment area. Then on Monday December 8, 2008, the gauges, along with other scrap metal, were removed by a single contractor.
"Those materials were taken to Lone Star Fox Export Metals for processing and packaging and it was assumed that the gauges would have been shipped in one of ten containers.
"The mixed shear cut metal was reportedly sent to Nhava Sheva, India as feed for a steel mill on or about Saturday, December 13, 2008 via Port of Entry (POE) Los Angeles/Long Beach. Research from US Customs and Boarder Protection (CBP) found evidence that seven of the ten containers were reportedly shipped from this POE on December 27, 2008 and arrived in India on February 12, 2009.
"As confidence is high that the gauges were taken to Lone Star Metals and bulk material is sheared at the yard, arrangements were made to survey the property of 2019 Ruder Lane, Dallas, TX. Staff utilized an E-600 meter with probe optimized for Am-241 (PG-2), a Thermo Interceptor and Ludlum 14C with a 44-3 probe. All instruments should be capable of detecting the single 100mCi, Am-241 source at three feet even when housed in the device. Specific surfaces surveyed in the yard included where material is off loaded, likely places where the gauges may have been sheared, tracks on large equipment, where scrap was pushed into a pile and the container loading areas. Then a random [based] walk through of the area was conducted but all surveys did not detect any radiation above background. [It was noted] that the entire yard was covered in one or more inches of mud from recent rains and dust reduction measures.
"Additional information is being acquired from several sources and the [State of Texas] is considering the utility of other methods and means of surveying."
Notified R4DO (Hay), FSME EO (Camper), OIP (Ramsey), and ILTAB (via email).
THIS MATERIAL EVENT CONTAINS A "LESS THAN CAT 3" LEVEL OF RADIOACTIVE MATERIAL
Sources that are "Less than IAEA Category 3 sources," are either sources that are very unlikely to cause permanent injury to individuals or contain a very small amount of radioactive material that would not cause any permanent injury. Some of these sources, such as moisture density gauges or thickness gauges that are Category 4, the amount of unshielded radioactive material, if not safely managed or securely protected, could possibly - although it is unlikely - temporarily injure someone who handled it or were otherwise in contact with it, or who were close to it for a period of many weeks.
"On February 20, 2009 during an internal audit/inspection, it was discovered that two Filtec Model FT 50 level detection devices each with 100 mCi of Am-241 were missing [and] apparently moved off the facility as scrap metal. Notification to state offices were through inappropriate channels and thus Incident Investigation staff were not informed of [the event] until March 12, 2009. A preliminary investigation has determined that the metal scrap along with these devices was subsequently shipped to a mill in India and [has] probably been melted. Specific details of the shipping, route and mode of transport, vendors as well actual location in India are being gathered. The serial numbers are 112733/5393 and 116813/2555."
Texas Incident # I-8618
* * * UPDATE ON 03/13/2009 AT 1400 FROM RAY JISHA TO DAN LIVERMORE * * *
Report received via e-mail:
"The gauges were accidentally removed from the plant and placed into a metal scrap dumpster and picked up from our property by MC3 International Scrap Salvage on December 8, 2008.
"MC3 International Scrap Salvage delivered the mixed shear cut metal to Lone Star Fox Export Metals on December 8, 2008. Lone Star Fox Export shipped the mixed cut metal to India before or around December 13, 2008. The licensee provided a list of 10 containers.
"The mixed metal was sent to Nhava Sheva, India. The licensee does not have any information on the mill in India. They do not have any information on products that may have been produced from the scrap.
"The state is in the process of contacting the scrap metal dealers. Additional information will follow as it is obtained."
Notified R4DO (Farnholtz), FSME EO (McIntosh), OIP (Ramsey), and ILTAB (via email).
* * * UPDATE ON 03/18/2009 AT 1253 FROM RAY JISHA TO VINCE KLCO * * *
Report received via e-mail:
"On Monday, March 16, 2009 [State of Texas] staff proceeded to Dr. Pepper Bottling Company (DP) in Irving, TX, General License Acknowledgement (GLA) G01697. This was in response to a report that two gauges were removed from the facility, potentially sheared at a local area scrap yard, and then shipped to India as feed for a steel mill. Upon arrival [state personnel] interviewed the Manager of Environmental Health and Safety and the Maintenance Manager in order to investigate the details of the two missing fixed fill level gauges (Industrial Dynamics, FT-50 containing 100 mCi, Am-241 each). The current contact person listed on the permit, was out of town at the time of this investigation.
"This gauge is a stainless steel box with overall head dimensions of 17 inches high, 4 ¢ inches wide and 19 ¢ inches long. These particular models have a manual shutter that was assumed to have been closed when the device was taken off-line. The Industrial Dynamics Source model 06110 is a matrix Americium 241 oxide and ceramic powder fired into a cavity 2 inches wide, 2 inches high and 1 3/8 inches deep. There is a 0.005 inch thick radiation window and when the shutter is closed, the radioactive material is covered on all sides by at least 0.5 inch of stainless steel.
"Apparently, the gauges were taken out of service some years back and stored in a used or discarded equipment area. Then on Monday December 8, 2008, the gauges, along with other scrap metal, were removed by a single contractor.
"Those materials were taken to Lone Star Fox Export Metals for processing and packaging and it was assumed that the gauges would have been shipped in one of ten containers.
"The mixed shear cut metal was reportedly sent to Nhava Sheva, India as feed for a steel mill on or about Saturday, December 13, 2008 via Port of Entry (POE) Los Angeles/Long Beach. Research from US Customs and Boarder Protection (CBP) found evidence that seven of the ten containers were reportedly shipped from this POE on December 27, 2008 and arrived in India on February 12, 2009.
"As confidence is high that the gauges were taken to Lone Star Metals and bulk material is sheared at the yard, arrangements were made to survey the property of 2019 Ruder Lane, Dallas, TX. Staff utilized an E-600 meter with probe optimized for Am-241 (PG-2), a Thermo Interceptor and Ludlum 14C with a 44-3 probe. All instruments should be capable of detecting the single 100mCi, Am-241 source at three feet even when housed in the device. Specific surfaces surveyed in the yard included where material is off loaded, likely places where the gauges may have been sheared, tracks on large equipment, where scrap was pushed into a pile and the container loading areas. Then a random [based] walk through of the area was conducted but all surveys did not detect any radiation above background. [It was noted] that the entire yard was covered in one or more inches of mud from recent rains and dust reduction measures.
"Additional information is being acquired from several sources and the [State of Texas] is considering the utility of other methods and means of surveying."
Notified R4DO (Hay), FSME EO (Camper), OIP (Ramsey), and ILTAB (via email).
THIS MATERIAL EVENT CONTAINS A "LESS THAN CAT 3" LEVEL OF RADIOACTIVE MATERIAL
Sources that are "Less than IAEA Category 3 sources," are either sources that are very unlikely to cause permanent injury to individuals or contain a very small amount of radioactive material that would not cause any permanent injury. Some of these sources, such as moisture density gauges or thickness gauges that are Category 4, the amount of unshielded radioactive material, if not safely managed or securely protected, could possibly - although it is unlikely - temporarily injure someone who handled it or were otherwise in contact with it, or who were close to it for a period of many weeks.
General Information or Other
Event Number: 44898
Rep Org: MARYLAND DEPT OF THE ENVIRONMENT
Licensee: STONE INDUSTRIAL
Region: 1
City: COLLEGE PARK State: MD
County:
License #:
Agreement: Y
Docket:
NRC Notified By: ALAN JACOBSON
HQ OPS Officer: JOE O'HARA
Licensee: STONE INDUSTRIAL
Region: 1
City: COLLEGE PARK State: MD
County:
License #:
Agreement: Y
Docket:
NRC Notified By: ALAN JACOBSON
HQ OPS Officer: JOE O'HARA
Notification Date: 03/12/2009
Notification Time: 08:55 [ET]
Event Date: 03/06/2009
Event Time: 00:00 [EDT]
Last Update Date: 03/12/2009
Notification Time: 08:55 [ET]
Event Date: 03/06/2009
Event Time: 00:00 [EDT]
Last Update Date: 03/12/2009
Emergency Class: NON EMERGENCY
10 CFR Section:
10 CFR Section:
Person (Organization):
ANTHONY DIMITRIADIS (R1)
ANGELA MCINTOSH (FSME)
ILTAB VIA EMAIL
ANTHONY DIMITRIADIS (R1)
ANGELA MCINTOSH (FSME)
ILTAB VIA EMAIL
MISSING STATIC ELIMINATOR CONTAINING POLONIUM-210
"This report is in reference to a lost 13 [inch] Nuclestat ionizer bar that contains Polonium-210. The model number is P-2001-012, and the serial number is A2FS026. [The licensee] entered into a lease agreement for 13 ionizer bars, 2 Nuclecel in-line ionizers, and 1 Nuclecel ion air blower with NRD, LLC to minimize the amount of static present in our operation.
"On Friday, March 6, 2009, it was reported by [the licensee's] Maintenance Department that an ionizer bar was missing from Winder #23. They were in the process of removing all of the ionizer bars from the winders to return them to NRD, LLC. The security cable was found attached to the winder, but it appeared someone had unscrewed the ionizer bar. All bars were attached to the end of the plastic winders with a steel cable and two screws. Upon investigation, [a licensee representative] found [that] the operators [remembered] the ionizer bar [being] present the week of February 23 - 27th on Winder #23, but they [did] not remember seeing the ionizer bar when [they] returned from a two day shutdown on Wednesday, March 4, 2009. After learning [that] the ionizer bar was missing on March 6th, the Plastic Winding Department was shutdown in the afternoon to search for it. About 15 employees searched the entire building including the trash and the building next door that contains old equipment. On Monday, March 9, 2009, the trash from the trash compactor was dumped in the parking lot, and the department searched through it for the missing ionizer bar. Once it was determined the ionizer bar was still missing, [a licensee representative] reported the lost device to [a State of Maryland representative] on March 9th.
"The remaining in-line ionizer bars, Nuclecel in-line ionizers and Nuclecel ion air blower will be returned to NRD, LLC to terminate our lease agreement. We will replace them with carbon bars and electronic air ionizers to reduce static in our operation."
THIS MATERIAL EVENT CONTAINS A "LESS THAN CAT 3" LEVEL OF RADIOACTIVE MATERIAL
Sources that are "Less than IAEA Category 3 sources," are either sources that are very unlikely to cause permanent injury to individuals or contain a very small amount of radioactive material that would not cause any permanent injury. Some of these sources, such as moisture density gauges or thickness gauges that are Category 4, the amount of unshielded radioactive material, if not safely managed or securely protected, could possibly - although it is unlikely - temporarily injure someone who handled it or were otherwise in contact with it, or who were close to it for a period of many weeks.
"This report is in reference to a lost 13 [inch] Nuclestat ionizer bar that contains Polonium-210. The model number is P-2001-012, and the serial number is A2FS026. [The licensee] entered into a lease agreement for 13 ionizer bars, 2 Nuclecel in-line ionizers, and 1 Nuclecel ion air blower with NRD, LLC to minimize the amount of static present in our operation.
"On Friday, March 6, 2009, it was reported by [the licensee's] Maintenance Department that an ionizer bar was missing from Winder #23. They were in the process of removing all of the ionizer bars from the winders to return them to NRD, LLC. The security cable was found attached to the winder, but it appeared someone had unscrewed the ionizer bar. All bars were attached to the end of the plastic winders with a steel cable and two screws. Upon investigation, [a licensee representative] found [that] the operators [remembered] the ionizer bar [being] present the week of February 23 - 27th on Winder #23, but they [did] not remember seeing the ionizer bar when [they] returned from a two day shutdown on Wednesday, March 4, 2009. After learning [that] the ionizer bar was missing on March 6th, the Plastic Winding Department was shutdown in the afternoon to search for it. About 15 employees searched the entire building including the trash and the building next door that contains old equipment. On Monday, March 9, 2009, the trash from the trash compactor was dumped in the parking lot, and the department searched through it for the missing ionizer bar. Once it was determined the ionizer bar was still missing, [a licensee representative] reported the lost device to [a State of Maryland representative] on March 9th.
"The remaining in-line ionizer bars, Nuclecel in-line ionizers and Nuclecel ion air blower will be returned to NRD, LLC to terminate our lease agreement. We will replace them with carbon bars and electronic air ionizers to reduce static in our operation."
THIS MATERIAL EVENT CONTAINS A "LESS THAN CAT 3" LEVEL OF RADIOACTIVE MATERIAL
Sources that are "Less than IAEA Category 3 sources," are either sources that are very unlikely to cause permanent injury to individuals or contain a very small amount of radioactive material that would not cause any permanent injury. Some of these sources, such as moisture density gauges or thickness gauges that are Category 4, the amount of unshielded radioactive material, if not safely managed or securely protected, could possibly - although it is unlikely - temporarily injure someone who handled it or were otherwise in contact with it, or who were close to it for a period of many weeks.
Power Reactor
Event Number: 44894
Facility: HOPE CREEK
Region: 1 State: NJ
Unit: [1] [] []
RX Type: [1] GE-4
NRC Notified By: TOM FOWLER
HQ OPS Officer: JASON KOZAL
Region: 1 State: NJ
Unit: [1] [] []
RX Type: [1] GE-4
NRC Notified By: TOM FOWLER
HQ OPS Officer: JASON KOZAL
Notification Date: 03/06/2009
Notification Time: 17:06 [ET]
Event Date: 03/06/2009
Event Time: 14:40 [EST]
Last Update Date: 03/06/2009
Notification Time: 17:06 [ET]
Event Date: 03/06/2009
Event Time: 14:40 [EST]
Last Update Date: 03/06/2009
Emergency Class: NON EMERGENCY
10 CFR Section:
50.72(b)(2)(xi) - OFFSITE NOTIFICATION
10 CFR Section:
50.72(b)(2)(xi) - OFFSITE NOTIFICATION
Person (Organization):
SAM HANSELL (R1)
SAM HANSELL (R1)
| Unit | SCRAM Code | RX Crit | Initial PWR | Initial RX Mode | Current PWR | Current RX Mode |
|---|---|---|---|---|---|---|
| 1 | N | Y | 100 | Power Operation | 100 | Power Operation |
OFFSITE NOTIFICATION DUE TO GASOLINE SPILL
"At 1440 a gasoline spill occurred while filling a company vehicle from a mobile gasoline truck. The auto-fill valve failed to shut off immediately when the gas tank was full and sprayed / spilled a small quantity (< 1 gallon) of gasoline on the ground. The spill was immediately terminated. This gasoline travelled to the nearest storm drain via water from melting snow. The Operations department was notified at 1445. Initial investigation revealed that the next storm drain in line to the river from the affected storm drain had significant water flow through it from the melting snow and no sheen was observed. There was also no oil sheen visible in the Delaware River. Based on the available indications, a 15 minute report to the State of New Jersey was completed at 1458 in accordance with the Hope Creek Event Classification Guide. The National Response Center was also notified at 1600.
"Spill recovery actions are in progress and expected to complete before the end of the day. The NRC Resident Inspector has been informed. Plant operation was unaffected, no safety systems were impacted."
"At 1440 a gasoline spill occurred while filling a company vehicle from a mobile gasoline truck. The auto-fill valve failed to shut off immediately when the gas tank was full and sprayed / spilled a small quantity (< 1 gallon) of gasoline on the ground. The spill was immediately terminated. This gasoline travelled to the nearest storm drain via water from melting snow. The Operations department was notified at 1445. Initial investigation revealed that the next storm drain in line to the river from the affected storm drain had significant water flow through it from the melting snow and no sheen was observed. There was also no oil sheen visible in the Delaware River. Based on the available indications, a 15 minute report to the State of New Jersey was completed at 1458 in accordance with the Hope Creek Event Classification Guide. The National Response Center was also notified at 1600.
"Spill recovery actions are in progress and expected to complete before the end of the day. The NRC Resident Inspector has been informed. Plant operation was unaffected, no safety systems were impacted."