Event Notification Report for October 15, 2007
U.S. Nuclear Regulatory Commission
Operations Center
EVENT REPORTS FOR
10/14/2007 - 10/15/2007
EVENT NUMBERS
4372343724437394383445507
Power Reactor
Event Number: 43723
Facility: SAINT LUCIE
Region: 2 State: FL
Unit: [] [2] []
RX Type: [1] CE,[2] CE
NRC Notified By: J. BREEN
HQ OPS Officer: JOHN MacKINNON
Region: 2 State: FL
Unit: [] [2] []
RX Type: [1] CE,[2] CE
NRC Notified By: J. BREEN
HQ OPS Officer: JOHN MacKINNON
Notification Date: 10/15/2007
Notification Time: 13:16 [ET]
Event Date: 10/15/2007
Event Time: 09:50 [EDT]
Last Update Date: 10/15/2007
Notification Time: 13:16 [ET]
Event Date: 10/15/2007
Event Time: 09:50 [EDT]
Last Update Date: 10/15/2007
Emergency Class: NON EMERGENCY
10 CFR Section:
50.72(b)(2)(xi) - OFFSITE NOTIFICATION
10 CFR Section:
50.72(b)(2)(xi) - OFFSITE NOTIFICATION
Person (Organization):
BINOY DESAI (R2)
BINOY DESAI (R2)
| Unit | SCRAM Code | RX Crit | Initial PWR | Initial RX Mode | Current PWR | Current RX Mode |
|---|---|---|---|---|---|---|
| 2 | N | N | 0 | Refueling | 0 | Refueling |
OFFSITE NOTIFICATION TO FLORIDA DEPARTMENT IF ENVIRONMENTAL PROTECTION (FEDP)
"At 0950, the Florida Department of Environmental Protection (FDEP) was notified in regards to a Turbine Lube Oil spill of approximately 350 gallons. The notification, to the FDEP, was required due to the inability to reach clean-up target levels within 30 days. In addition, the State Warning Point was notified at 1010. This non-emergency notification is being made, pursuant to 10 CFR 50.72(b)(2)(xi), due to the notification of outside government agencies in response to this environmental event. The cause of the oil spill is still under investigation."
The NRC Resident Inspector was notified of this event by the licensee.
"At 0950, the Florida Department of Environmental Protection (FDEP) was notified in regards to a Turbine Lube Oil spill of approximately 350 gallons. The notification, to the FDEP, was required due to the inability to reach clean-up target levels within 30 days. In addition, the State Warning Point was notified at 1010. This non-emergency notification is being made, pursuant to 10 CFR 50.72(b)(2)(xi), due to the notification of outside government agencies in response to this environmental event. The cause of the oil spill is still under investigation."
The NRC Resident Inspector was notified of this event by the licensee.
General Information or Other
Event Number: 43724
Rep Org: MA RADIATION CONTROL PROGRAM
Licensee: ALLEGHENY RODNEY
Region: 1
City: NEW BEDFORD State: MA
County:
License #: G-0112
Agreement: Y
Docket:
NRC Notified By: BRUCE PACKARD
HQ OPS Officer: PETE SNYDER
Licensee: ALLEGHENY RODNEY
Region: 1
City: NEW BEDFORD State: MA
County:
License #: G-0112
Agreement: Y
Docket:
NRC Notified By: BRUCE PACKARD
HQ OPS Officer: PETE SNYDER
Notification Date: 10/15/2007
Notification Time: 18:29 [ET]
Event Date: 10/15/2007
Event Time: 12:00 [EDT]
Last Update Date: 10/15/2007
Notification Time: 18:29 [ET]
Event Date: 10/15/2007
Event Time: 12:00 [EDT]
Last Update Date: 10/15/2007
Emergency Class: NON EMERGENCY
10 CFR Section:
10 CFR Section:
Person (Organization):
RONALD BELLAMY (R1)
SCOTT FLANDERS (FSME)
RONALD BELLAMY (R1)
SCOTT FLANDERS (FSME)
MASSACHUSETTS AGREEMENT STATE REPORT
The following agreement state report information was faxed to the NRC Operation Center.
"Description: Thickness gauge
"Investigation Pending: No
"Consultant Hired: Yes
"Corrective Action: Licensed Contractor fixed the gauge
"SUBJECT: A gauge on the Z-25 press is sometimes stuck closed. The equipment is out of use.
"Equipment problem : Shutter was not working properly. Equipment problem, capacitor fell off."
The following agreement state report information was faxed to the NRC Operation Center.
"Description: Thickness gauge
"Investigation Pending: No
"Consultant Hired: Yes
"Corrective Action: Licensed Contractor fixed the gauge
"SUBJECT: A gauge on the Z-25 press is sometimes stuck closed. The equipment is out of use.
"Equipment problem : Shutter was not working properly. Equipment problem, capacitor fell off."
General Information or Other
Event Number: 43739
Rep Org: CALIFORNIA RADIATION CONTROL PRGM
Licensee: GEOMAT TESTING LABS., INC.
Region: 4
City: RIVERSIDE State: CA
County:
License #: 5735-33
Agreement: Y
Docket:
NRC Notified By: BARBARA HAMRICK
HQ OPS Officer: JOHN MacKINNON
Licensee: GEOMAT TESTING LABS., INC.
Region: 4
City: RIVERSIDE State: CA
County:
License #: 5735-33
Agreement: Y
Docket:
NRC Notified By: BARBARA HAMRICK
HQ OPS Officer: JOHN MacKINNON
Notification Date: 10/22/2007
Notification Time: 14:21 [ET]
Event Date: 10/15/2007
Event Time: 17:30 [PDT]
Last Update Date: 10/22/2007
Notification Time: 14:21 [ET]
Event Date: 10/15/2007
Event Time: 17:30 [PDT]
Last Update Date: 10/22/2007
Emergency Class: NON EMERGENCY
10 CFR Section:
10 CFR Section:
Person (Organization):
CHUCK CAIN (R4)
MICHELE BURGESS (FSME)
ILTAB (EMAIL)
MEXICO (EMAILED)
CHUCK CAIN (R4)
MICHELE BURGESS (FSME)
ILTAB (EMAIL)
MEXICO (EMAILED)
CALIFORNIA AGREEMENT STATE REPORT
Received the following information via e-mail:
"On October 22, 2007, a letter, dated 10/17/07, was received from Haytham (deleted), RSO, reporting a stolen nuclear gauge (Troxler 3400 Series, S/N 14411). The incident happened on 10/15/07 at San Bernardino County. According to the incident report, the nuclear gauge was taken to Southwest Calibration in San Bernardino for repair. After the repair, at about 5:30 pm, the field technician stopped at an automobile garage in San Bernardino to have the company truck tail light repaired. The nuclear gauge metal box was bolted close to the tail light access location and was asked by the shop technician to remove the box so they can repair the tail light. The metal box was placed on the side near the waiting room. Then, the technician went inside the waiting room. After the tail light was repaired, the technician went outside and did not find the nuclear gauge.
"The technician called the RSO and left a message. The incident was reported to San Bernardino County Sheriff's Office (Police Report # 030705898) and an ad was placed in the 'SUN', San Bernardino newspaper for seven days.
"RHB - South RAM office will investigate this incident."
5010 Number (Date Notified): 102207
THIS MATERIAL EVENT CONTAINS A "LESS THAN CAT 3" LEVEL OF RADIOACTIVE MATERIAL
Sources that are "Less than IAEA Category 3 sources," are either sources that are very unlikely to cause permanent injury to individuals or contain a very small amount of radioactive material that would not cause any permanent injury. Some of these sources, such as moisture density gauges or thickness gauges that are Category 4, the amount of unshielded radioactive material, if not safely managed or securely protected, could possibly - although it is unlikely - temporarily injure someone who handled it or were otherwise in contact with it, or who were close to it for a period of many weeks.
Received the following information via e-mail:
"On October 22, 2007, a letter, dated 10/17/07, was received from Haytham (deleted), RSO, reporting a stolen nuclear gauge (Troxler 3400 Series, S/N 14411). The incident happened on 10/15/07 at San Bernardino County. According to the incident report, the nuclear gauge was taken to Southwest Calibration in San Bernardino for repair. After the repair, at about 5:30 pm, the field technician stopped at an automobile garage in San Bernardino to have the company truck tail light repaired. The nuclear gauge metal box was bolted close to the tail light access location and was asked by the shop technician to remove the box so they can repair the tail light. The metal box was placed on the side near the waiting room. Then, the technician went inside the waiting room. After the tail light was repaired, the technician went outside and did not find the nuclear gauge.
"The technician called the RSO and left a message. The incident was reported to San Bernardino County Sheriff's Office (Police Report # 030705898) and an ad was placed in the 'SUN', San Bernardino newspaper for seven days.
"RHB - South RAM office will investigate this incident."
5010 Number (Date Notified): 102207
THIS MATERIAL EVENT CONTAINS A "LESS THAN CAT 3" LEVEL OF RADIOACTIVE MATERIAL
Sources that are "Less than IAEA Category 3 sources," are either sources that are very unlikely to cause permanent injury to individuals or contain a very small amount of radioactive material that would not cause any permanent injury. Some of these sources, such as moisture density gauges or thickness gauges that are Category 4, the amount of unshielded radioactive material, if not safely managed or securely protected, could possibly - although it is unlikely - temporarily injure someone who handled it or were otherwise in contact with it, or who were close to it for a period of many weeks.
Power Reactor
Event Number: 43834
Facility: PRAIRIE ISLAND
Region: 3 State: MN
Unit: [1] [] []
RX Type: [1] W-2-LP,[2] W-2-LP
NRC Notified By: GENE DAMMANN
HQ OPS Officer: MARK ABRAMOVITZ
Region: 3 State: MN
Unit: [1] [] []
RX Type: [1] W-2-LP,[2] W-2-LP
NRC Notified By: GENE DAMMANN
HQ OPS Officer: MARK ABRAMOVITZ
Notification Date: 12/11/2007
Notification Time: 13:57 [ET]
Event Date: 10/15/2007
Event Time: 14:02 [CST]
Last Update Date: 12/11/2007
Notification Time: 13:57 [ET]
Event Date: 10/15/2007
Event Time: 14:02 [CST]
Last Update Date: 12/11/2007
Emergency Class: NON EMERGENCY
10 CFR Section:
50.73(a)(1) - INVALID SPECIF SYSTEM ACTUATION
10 CFR Section:
50.73(a)(1) - INVALID SPECIF SYSTEM ACTUATION
Person (Organization):
JOHN MADERA (R3)
JOHN MADERA (R3)
| Unit | SCRAM Code | RX Crit | Initial PWR | Initial RX Mode | Current PWR | Current RX Mode |
|---|---|---|---|---|---|---|
| 1 | N | Y | 100 | Power Operation | 100 | Power Operation |
INADVERTENT START OF EMERGENCY DIESEL GENERATOR D2
"This notification is being made to report an invalid system actuation in accordance with 10 CFR 50.73(a)(2)(iv)(A). Prairie Island Nuclear Generating Plant (PINGP) Train B Unit 1 emergency diesel generator (D2) started due to an invalid system actuation.
"On 10/15/07, at approximately 1402 hours (CDT), with PINGP Unit 1 in MODE 1, D2 started inadvertently during an air roll.
"The inadvertent start of D2 Diesel Generator occurred while the diesel was declared inoperable (Technical Specification LCO 3.8.1 CONDITION B was entered at 0916 10/15/07 and exited at 1433 10/15/07). Normally, an air roll uses starting air to turn the engine one revolution to clear oil from the top piston of the D2 opposed piston diesel engine. The D2 control switch is to be in pullout per procedure. However, due to operator error, the D2 control switch was not in pullout during the air roll and D2 started during the attempted air roll. D2 did not automatically connect to the associated emergency bus (Bus 16), because no bus undervoltage signal was present and the supply breaker was open.
"The Train A diesel generator (D1) remained operable during this event and the Train A EDG was able to provide power to the Train A emergency bus (Bus 15), if necessary. The invalid start was entered into the PINGP corrective action program. The preliminary investigation of this event determined that the D2 start was caused by operator error - the outplant operators performing the air roll missed a step in the procedure that directed calling the control room to verify the D2 control switch in pullout prior to conducting the air roll.
"Corrective actions for this event are in progress and are being tracked via the corrective action program."
The licensee will notify the NRC Resident Inspector.
"This notification is being made to report an invalid system actuation in accordance with 10 CFR 50.73(a)(2)(iv)(A). Prairie Island Nuclear Generating Plant (PINGP) Train B Unit 1 emergency diesel generator (D2) started due to an invalid system actuation.
"On 10/15/07, at approximately 1402 hours (CDT), with PINGP Unit 1 in MODE 1, D2 started inadvertently during an air roll.
"The inadvertent start of D2 Diesel Generator occurred while the diesel was declared inoperable (Technical Specification LCO 3.8.1 CONDITION B was entered at 0916 10/15/07 and exited at 1433 10/15/07). Normally, an air roll uses starting air to turn the engine one revolution to clear oil from the top piston of the D2 opposed piston diesel engine. The D2 control switch is to be in pullout per procedure. However, due to operator error, the D2 control switch was not in pullout during the air roll and D2 started during the attempted air roll. D2 did not automatically connect to the associated emergency bus (Bus 16), because no bus undervoltage signal was present and the supply breaker was open.
"The Train A diesel generator (D1) remained operable during this event and the Train A EDG was able to provide power to the Train A emergency bus (Bus 15), if necessary. The invalid start was entered into the PINGP corrective action program. The preliminary investigation of this event determined that the D2 start was caused by operator error - the outplant operators performing the air roll missed a step in the procedure that directed calling the control room to verify the D2 control switch in pullout prior to conducting the air roll.
"Corrective actions for this event are in progress and are being tracked via the corrective action program."
The licensee will notify the NRC Resident Inspector.
General Information or Other
Event Number: 45507
Rep Org: TEXAS DEPARTMENT OF HEALTH
Licensee: JAMES HARDIE BUILDING PRODUCTS INC
Region: 4
City: CLEBURNE State: TX
County:
License #: 02040
Agreement: Y
Docket:
NRC Notified By: ART TUCKER
HQ OPS Officer: MARK ABRAMOVITZ
Licensee: JAMES HARDIE BUILDING PRODUCTS INC
Region: 4
City: CLEBURNE State: TX
County:
License #: 02040
Agreement: Y
Docket:
NRC Notified By: ART TUCKER
HQ OPS Officer: MARK ABRAMOVITZ
Notification Date: 11/18/2009
Notification Time: 14:46 [ET]
Event Date: 10/15/2007
Event Time: 00:00 [CST]
Last Update Date: 11/18/2009
Notification Time: 14:46 [ET]
Event Date: 10/15/2007
Event Time: 00:00 [CST]
Last Update Date: 11/18/2009
Emergency Class: NON EMERGENCY
10 CFR Section:
10 CFR Section:
Person (Organization):
DAVID PROULX (R4DO)
ANDREW MAUER (FSME)
DAVID PROULX (R4DO)
ANDREW MAUER (FSME)
AGREEMENT STATE REPORT - DENSITY GAUGE SHUTTER STUCK IN OPEN POSITION
The following report was received via e-mail:
"On November 26, 2007, the Agency received a letter from the licensee notifying them that while conducting a routine inventory and shutter inspection of a density gauge, the shutter was found stuck in the open position. The licensee contacted a vendor to repair the gauge. The vendor determined that a bolt on the shutter had broken preventing the shutter from closing. The shutter could not be repaired. The shutter is normally open so there was no increased risk of additional radiation exposure to the workers at the facility. A new device was ordered and the old gauge was disposed of when the new one was installed.
"The gauge was an Ohmart/VEGA Corporation model SH-F1, serial number 8622 K containing a 50 milliCurie Cesium (Cs) - 137 source."
Texas Incident: I-8456
The following report was received via e-mail:
"On November 26, 2007, the Agency received a letter from the licensee notifying them that while conducting a routine inventory and shutter inspection of a density gauge, the shutter was found stuck in the open position. The licensee contacted a vendor to repair the gauge. The vendor determined that a bolt on the shutter had broken preventing the shutter from closing. The shutter could not be repaired. The shutter is normally open so there was no increased risk of additional radiation exposure to the workers at the facility. A new device was ordered and the old gauge was disposed of when the new one was installed.
"The gauge was an Ohmart/VEGA Corporation model SH-F1, serial number 8622 K containing a 50 milliCurie Cesium (Cs) - 137 source."
Texas Incident: I-8456