Event Notification Report for March 02, 2007
U.S. Nuclear Regulatory Commission
Operations Center
EVENT REPORTS FOR
03/01/2007 - 03/02/2007
EVENT NUMBERS
4320643207432084320943210
General Information or Other
Event Number: 43206
Rep Org: WISCONSIN RADIATION PROTECTION
Licensee: TO BE DETERMINED
Region: 3
City: MILWAUKEE State: WI
County:
License #: TBD
Agreement: Y
Docket:
NRC Notified By: MIKE MACK
HQ OPS Officer: JASON KOZAL
Licensee: TO BE DETERMINED
Region: 3
City: MILWAUKEE State: WI
County:
License #: TBD
Agreement: Y
Docket:
NRC Notified By: MIKE MACK
HQ OPS Officer: JASON KOZAL
Notification Date: 03/02/2007
Notification Time: 14:27 [ET]
Event Date: 03/02/2007
Event Time: 11:00 [CST]
Last Update Date: 03/02/2007
Notification Time: 14:27 [ET]
Event Date: 03/02/2007
Event Time: 11:00 [CST]
Last Update Date: 03/02/2007
Emergency Class: NON EMERGENCY
10 CFR Section:
10 CFR Section:
Person (Organization):
ROGER LANKSBURY (R3)
SANDRA WASTLER (FSME)
ROGER LANKSBURY (R3)
SANDRA WASTLER (FSME)
AGREEMENT STATE REPORT - TROXLER GAUGE FOUND IN SCRAP HEAP
The following was provided by the State via facsimile:
"Event Location: Miller Compressing, Milwaukee, WI
"Event Type: Found Radioactive Material-Portable Moisture Density Gauge
"Notifications: Miller Compressing called [the] Department of Health and Family Services (DHFS)
"Event description: A Troxler moisture density gauge was found at Miller Compressing on 2/22/07. It was in a load of scrap and was separated by the staff at Miller Compressing.
"Additional Information: Miller Compressing is scrap metal recycler in Milwaukee.
"The DHFS staff in Wisconsin has been in contact with the state of Illinois Emergency Management Agency and Troxler Electronic Labs to try and identify an owner or former licensee. The gauge was initially distributed to an Illinois licensee in 1977. The portable gauge is a Troxler Model 3411. The plate on the device indicates the device serial number is 4942. The back plate identifies the nuclides as 8.9 mCi of Cs-137 on 9/5/77 ([serial number] CC-1968) and 40 mCi of Am241:Be on 9/14/77 ([serial number] CAA-1031). The serial no. does not match any gauges currently reported as lost or stolen.
"The shipping container is damaged. The gauge is intact. Miller Compressing is storing the gauge in a locked location on site. DHFS staff will follow up with a site visit."
WI report number: W070005
THIS MATERIAL EVENT CONTAINS A "LESS THAN CAT 3" LEVEL OF RADIOACTIVE MATERIAL
Sources that are "Less than IAEA Category 3 sources," are either sources that are very unlikely to cause permanent injury to individuals or contain a very small amount of radioactive material that would not cause any permanent injury. Some of these sources, such as moisture density gauges or thickness gauges that are Category 4, the amount of unshielded radioactive material, if not safely managed or securely protected, could possibly - although it is unlikely - temporarily injure someone who handled it or were otherwise in contact with it, or who were close to it for a period of many weeks.
The following was provided by the State via facsimile:
"Event Location: Miller Compressing, Milwaukee, WI
"Event Type: Found Radioactive Material-Portable Moisture Density Gauge
"Notifications: Miller Compressing called [the] Department of Health and Family Services (DHFS)
"Event description: A Troxler moisture density gauge was found at Miller Compressing on 2/22/07. It was in a load of scrap and was separated by the staff at Miller Compressing.
"Additional Information: Miller Compressing is scrap metal recycler in Milwaukee.
"The DHFS staff in Wisconsin has been in contact with the state of Illinois Emergency Management Agency and Troxler Electronic Labs to try and identify an owner or former licensee. The gauge was initially distributed to an Illinois licensee in 1977. The portable gauge is a Troxler Model 3411. The plate on the device indicates the device serial number is 4942. The back plate identifies the nuclides as 8.9 mCi of Cs-137 on 9/5/77 ([serial number] CC-1968) and 40 mCi of Am241:Be on 9/14/77 ([serial number] CAA-1031). The serial no. does not match any gauges currently reported as lost or stolen.
"The shipping container is damaged. The gauge is intact. Miller Compressing is storing the gauge in a locked location on site. DHFS staff will follow up with a site visit."
WI report number: W070005
THIS MATERIAL EVENT CONTAINS A "LESS THAN CAT 3" LEVEL OF RADIOACTIVE MATERIAL
Sources that are "Less than IAEA Category 3 sources," are either sources that are very unlikely to cause permanent injury to individuals or contain a very small amount of radioactive material that would not cause any permanent injury. Some of these sources, such as moisture density gauges or thickness gauges that are Category 4, the amount of unshielded radioactive material, if not safely managed or securely protected, could possibly - although it is unlikely - temporarily injure someone who handled it or were otherwise in contact with it, or who were close to it for a period of many weeks.
!!!!! THIS EVENT HAS BEEN RETRACTED !!!!!
!!!!! THIS EVENT HAS BEEN RETRACTED !!!!!
Power Reactor
Event Number: 43207
Facility: SAN ONOFRE
Region: 4 State: CA
Unit: [] [2] [3]
RX Type: [1] W-3-LP,[2] CE,[3] CE
NRC Notified By: SUSAN GARDNER
HQ OPS Officer: JOE O'HARA
Region: 4 State: CA
Unit: [] [2] [3]
RX Type: [1] W-3-LP,[2] CE,[3] CE
NRC Notified By: SUSAN GARDNER
HQ OPS Officer: JOE O'HARA
Notification Date: 03/02/2007
Notification Time: 17:03 [ET]
Event Date: 03/02/2007
Event Time: 10:14 [PST]
Last Update Date: 03/16/2007
Notification Time: 17:03 [ET]
Event Date: 03/02/2007
Event Time: 10:14 [PST]
Last Update Date: 03/16/2007
Emergency Class: NON EMERGENCY
10 CFR Section:
26.73 - FITNESS FOR DUTY
10 CFR Section:
26.73 - FITNESS FOR DUTY
Person (Organization):
DALE POWERS (R4)
THEODORE QUAY (NRR)
DALE POWERS (R4)
THEODORE QUAY (NRR)
| Unit | SCRAM Code | RX Crit | Initial PWR | Initial RX Mode | Current PWR | Current RX Mode |
|---|---|---|---|---|---|---|
| 2 | N | Y | 99 | Power Operation | 99 | Power Operation |
| 3 | N | Y | 98 | Power Operation | 98 | Power Operation |
FITNESS FOR DUTY - LICENSED EMPLOYEE
A licensed employee had a confirmed positive for alcohol during a random fitness-for-duty test. The employee's access to the plant has been revoked. Contact the Headquarters Operations Officer for additional details.
The licensee notified the NRC Resident Inspector.
* * * RETRACTION PROVIDED BY S.GARDNER TO KOZAL ON 3/16/07 1728 EDT * * *
The licensee provided a retraction regarding the above positive alcohol fitness-for-duty test. Contact the Headquarters Operations Officer for additional details.
The licensee notified the NRC Resident Inspector. R4DO (Shannon) notified.
A licensed employee had a confirmed positive for alcohol during a random fitness-for-duty test. The employee's access to the plant has been revoked. Contact the Headquarters Operations Officer for additional details.
The licensee notified the NRC Resident Inspector.
* * * RETRACTION PROVIDED BY S.GARDNER TO KOZAL ON 3/16/07 1728 EDT * * *
The licensee provided a retraction regarding the above positive alcohol fitness-for-duty test. Contact the Headquarters Operations Officer for additional details.
The licensee notified the NRC Resident Inspector. R4DO (Shannon) notified.
General Information or Other
Event Number: 43208
Rep Org: CALIFORNIA RADIATION CONTROL PRGM
Licensee: SMITH-EMERY COMPANY
Region: 4
City: GLENDALE State: CA
County:
License #: 2878-30
Agreement: Y
Docket:
NRC Notified By: DONELLE KRAJEWSKI
HQ OPS Officer: JASON KOZAL
Licensee: SMITH-EMERY COMPANY
Region: 4
City: GLENDALE State: CA
County:
License #: 2878-30
Agreement: Y
Docket:
NRC Notified By: DONELLE KRAJEWSKI
HQ OPS Officer: JASON KOZAL
Notification Date: 03/02/2007
Notification Time: 18:17 [ET]
Event Date: 03/02/2007
Event Time: 10:30 [PST]
Last Update Date: 03/02/2007
Notification Time: 18:17 [ET]
Event Date: 03/02/2007
Event Time: 10:30 [PST]
Last Update Date: 03/02/2007
Emergency Class: NON EMERGENCY
10 CFR Section:
10 CFR Section:
Person (Organization):
DALE POWERS (R4)
JACK DAVIS (FSME)
DALE POWERS (R4)
JACK DAVIS (FSME)
AGREEMENT STATE REPORT - DAMAGED CPN GAUGE
The following was provided by the State via facsimile:
"A moisture density gauge was being used at a construction site in Glendale, CA (near the Water Department and the Los Angeles River). (CPN, model MC3, serial number M36097108). The gauge user had placed the gauge into a box (plastic milk carton) which was then going to be passed down into a trench where it would be used. There was a delay and the box with the gauge inside were placed on the edge of the property waiting to be used. According to [the licensee], the gauge user went to the bathroom, but the other workers were aware of the location of the gauge. At the same time a front loader truck was moving several large pieces of metal. The pieces vibrated off and dropped onto and crushed the gauge.
"[The licensee] said the sources appeared to be intact, however the plastic gauge housing was destroyed and the lead shielding leaves that normally surround and shield the end of the source rod (where the Cs-137 source would normally reside in a shielded position) were not in position anymore and were therefore not shielding the Cs-137 source now. [A] Los Angeles County Radiation Management Health Physicist, responded to the site to do an evaluation and to survey the source. The sources were intact and undamaged. There was no contamination. The dose rate at 1 foot was 20 milliRoentgen per hour (mR/hr). The end of the source rod was shielded and the remains of the gauge were placed into the transportation case. The gauge was transported by the RSO to Maurer Technical Services (the CPN manufacturer representative) [Deleted] so it can be shipped back to the manufacturer for disposal. The highest dose to any individual from this event was probably less than 5 millirem total. Corrective actions: The RSO will give refresher training to all gauge users to review their existing policies and procedures - gauge users are to have control over the gauge at all times."
CA report number: 030207
The following was provided by the State via facsimile:
"A moisture density gauge was being used at a construction site in Glendale, CA (near the Water Department and the Los Angeles River). (CPN, model MC3, serial number M36097108). The gauge user had placed the gauge into a box (plastic milk carton) which was then going to be passed down into a trench where it would be used. There was a delay and the box with the gauge inside were placed on the edge of the property waiting to be used. According to [the licensee], the gauge user went to the bathroom, but the other workers were aware of the location of the gauge. At the same time a front loader truck was moving several large pieces of metal. The pieces vibrated off and dropped onto and crushed the gauge.
"[The licensee] said the sources appeared to be intact, however the plastic gauge housing was destroyed and the lead shielding leaves that normally surround and shield the end of the source rod (where the Cs-137 source would normally reside in a shielded position) were not in position anymore and were therefore not shielding the Cs-137 source now. [A] Los Angeles County Radiation Management Health Physicist, responded to the site to do an evaluation and to survey the source. The sources were intact and undamaged. There was no contamination. The dose rate at 1 foot was 20 milliRoentgen per hour (mR/hr). The end of the source rod was shielded and the remains of the gauge were placed into the transportation case. The gauge was transported by the RSO to Maurer Technical Services (the CPN manufacturer representative) [Deleted] so it can be shipped back to the manufacturer for disposal. The highest dose to any individual from this event was probably less than 5 millirem total. Corrective actions: The RSO will give refresher training to all gauge users to review their existing policies and procedures - gauge users are to have control over the gauge at all times."
CA report number: 030207
Power Reactor
Event Number: 43209
Facility: DRESDEN
Region: 3 State: IL
Unit: [] [] [3]
RX Type: [1] GE-1,[2] GE-3,[3] GE-3
NRC Notified By: RANDY WROBLEWSKI
HQ OPS Officer: JOE O'HARA
Region: 3 State: IL
Unit: [] [] [3]
RX Type: [1] GE-1,[2] GE-3,[3] GE-3
NRC Notified By: RANDY WROBLEWSKI
HQ OPS Officer: JOE O'HARA
Notification Date: 03/02/2007
Notification Time: 22:33 [ET]
Event Date: 03/02/2007
Event Time: 19:12 [CST]
Last Update Date: 03/02/2007
Notification Time: 22:33 [ET]
Event Date: 03/02/2007
Event Time: 19:12 [CST]
Last Update Date: 03/02/2007
Emergency Class: NON EMERGENCY
10 CFR Section:
50.72(b)(3)(v)(D) - ACCIDENT MITIGATION
10 CFR Section:
50.72(b)(3)(v)(D) - ACCIDENT MITIGATION
Person (Organization):
ROGER LANKSBURY (R3)
ROGER LANKSBURY (R3)
| Unit | SCRAM Code | RX Crit | Initial PWR | Initial RX Mode | Current PWR | Current RX Mode |
|---|---|---|---|---|---|---|
| 3 | N | Y | 98 | Power Operation | 98 | Power Operation |
UNIT 3 HPCI INOPERABLE DUE TO PINHOLE LEAK ON THE STEAM SIDE
"At 1912 hours on 03/02/07, a through wall leak was identified on the U3 High Pressure Coolant Injection (HPCI) Inlet Drain Pot drain piping. This piping is ASME Code class 2 piping and as required by the Technical Requirements Manual the piping was isolated which resulted in isolation of the U3 HPCI System. U3 HPCI was declared inoperable. This event is reportable under 10CFR50.72(b)(3)(v)(D). Piping repair preparations are in progress."
The leak was discovered by a licensed operator on rounds. The Technical Specification is a 14 day LCO.
The licensee notified the NRC Resident Inspector.
"At 1912 hours on 03/02/07, a through wall leak was identified on the U3 High Pressure Coolant Injection (HPCI) Inlet Drain Pot drain piping. This piping is ASME Code class 2 piping and as required by the Technical Requirements Manual the piping was isolated which resulted in isolation of the U3 HPCI System. U3 HPCI was declared inoperable. This event is reportable under 10CFR50.72(b)(3)(v)(D). Piping repair preparations are in progress."
The leak was discovered by a licensed operator on rounds. The Technical Specification is a 14 day LCO.
The licensee notified the NRC Resident Inspector.
Power Reactor
Event Number: 43210
Facility: DUANE ARNOLD
Region: 3 State: IA
Unit: [1] [] []
RX Type: [1] GE-4
NRC Notified By: WAYNE BENTLEY
HQ OPS Officer: BILL HUFFMAN
Region: 3 State: IA
Unit: [1] [] []
RX Type: [1] GE-4
NRC Notified By: WAYNE BENTLEY
HQ OPS Officer: BILL HUFFMAN
Notification Date: 03/03/2007
Notification Time: 05:16 [ET]
Event Date: 03/02/2007
Event Time: 23:32 [CST]
Last Update Date: 03/03/2007
Notification Time: 05:16 [ET]
Event Date: 03/02/2007
Event Time: 23:32 [CST]
Last Update Date: 03/03/2007
Emergency Class: NON EMERGENCY
10 CFR Section:
50.72(b)(3)(iv)(A) - VALID SPECIF SYS ACTUATION
10 CFR Section:
50.72(b)(3)(iv)(A) - VALID SPECIF SYS ACTUATION
Person (Organization):
ROGER LANKSBURY (R3)
ROGER LANKSBURY (R3)
| Unit | SCRAM Code | RX Crit | Initial PWR | Initial RX Mode | Current PWR | Current RX Mode |
|---|---|---|---|---|---|---|
| 1 | N | N | 0 | Refueling | 0 | Refueling |
REACTOR SCRAM SIGNAL DUE TO HIGH DISCHARGE VOLUME LEVEL
The licensee was performing testing that inserts a reactor scram manually to verify that the backup scram valves port air. Moments after the scram was reset a second scram came in from a scram discharge volume high level. The second scram was not called out in the test, nor were there steps to bypass the scram discharge volume scram signal prior to resetting the manual scram.
All rods were already fully inserted and, consequently, there was no rod motion as a result of the scram. The licensee states the unexpected scram signal was a result of an error in the test procedure.
The NRC Resident Inspector has been notified.
The licensee was performing testing that inserts a reactor scram manually to verify that the backup scram valves port air. Moments after the scram was reset a second scram came in from a scram discharge volume high level. The second scram was not called out in the test, nor were there steps to bypass the scram discharge volume scram signal prior to resetting the manual scram.
All rods were already fully inserted and, consequently, there was no rod motion as a result of the scram. The licensee states the unexpected scram signal was a result of an error in the test procedure.
The NRC Resident Inspector has been notified.